In this guide
- What EWI and IWI actually are
- EWI vs IWI side by side
- Cost, disruption and space in practice
- External wall insulation and damp
- Fix the damp before you insulate
- When each system is the better fit
- Regulations to know about
- A worked example: a 1930s solid-wall semi
- Starting with a survey
- Our view on EWI, IWI and damp
- FAQ
- Sources
External wall insulation (EWI) goes on the outside of a solid wall and changes how the building looks. Internal wall insulation (IWI) goes on the inside, keeps the facade as it is and costs less, but takes up some room space. Neither is the right choice until the wall is dry and the cause of any damp is known. On a home with damp, mould or condensation, the order matters more than the system: diagnose, repair, then insulate.
This guide is written for homeowners, landlords and property professionals in Dorset, Hampshire and Wiltshire, where many older homes have solid walls and no cavity to fill.
Key Takeaways
- EWI leaves rooms at full size and is generally the lower-risk option where it can be installed. IWI suits properties where the exterior must stay unchanged or EWI is impractical.
- Published averages put IWI at £4k to £13k and EWI at £6k to £22k, with a three-bed semi at about £7k and £11k respectively.
- Existing damp must be resolved and the wall dried before either system is fitted. Insulating over damp traps the problem.
- Poorly detailed EWI can leave cold spots around windows, doors and pipes, and IWI needs a moisture-safe build-up. Both depend on a proper survey of the wall first.
- A complimentary survey from a damp specialist is the practical first step, before you collect insulation quotes.
What EWI and IWI actually are
Solid walls have no cavity. Older brick, stone and some early concrete homes are built this way, and they lose more heat than cavity walls. The two main ways to insulate them differ in where the insulation sits.
External wall insulation fixes insulation boards to the outer face of the wall, covers them with reinforcement and a special render, and finishes the surface in textured render, pebbledash, brick slips or brick-effect render, according to the Solid Wall Insulation Guarantee Agency (SWIGA). A typical installation runs through surface preparation, scaffolding, bonded boards, mechanical fixings, a mesh-reinforced base coat, primer and the final render, and takes one to two weeks on an average house.
Internal wall insulation is applied to the inside of the external walls. SWIGA describes it as typically pre-insulated plasterboard, or mineral wool or foam panels held in a studwork frame. Fittings such as radiators, skirting boards and architraves have to come off first and go back afterwards.
The government’s retrofit guidance uses a simple definition: EWI puts insulation on the cold side of the wall, IWI on the warm side. That one difference drives almost every other comparison below, including the damp behavior.

A third option exists. Where the front of a house must keep its appearance but the rear is free, a hybrid of the two is common, with EWI on one elevation and IWI on another.
EWI vs IWI side by side
| Factor | External wall insulation (EWI) | Internal wall insulation (IWI) |
|---|---|---|
| Typical cost range | £6k to £22k, about £11k for a 3-bed semi | £4k to £13k, about £7k for a 3-bed semi |
| Room space | No internal space lost | Roughly 25mm to 100mm lost per wall |
| Where the work happens | Outside, with scaffolding | Inside, room by room |
| Appearance | Changes the facade | Keeps the exterior as it is |
| Disruption to occupants | Lower | Higher, but can be phased |
| Thermal performance | Best results, fewer thermal bridges | Good, but junctions need care |
| Best suited to | Homes with free, unrestricted external walls | Conservation areas, listed buildings, flats, boundary walls |
The cost and space figures come from MoneySuperMarket’s 2025 solid wall insulation guide. They are averages. Your own price depends on wall area, access, finish and the repairs the wall needs first, so use them to judge a quote’s scale, not as a price.
Cost, disruption and space in practice
Cost
IWI is generally the cheaper system because it needs no scaffolding and no weatherproof render. The government’s best-practice guide lists no scaffolding, installation at any time of year and improved airtightness among the advantages of IWI. Which? reports that for a semi-detached house the two systems can cost around the same once extra work is counted, which is why a wall-by-wall quote beats a headline average.
Disruption
EWI is done from outside. Which? puts a semi-detached installation at around 7 to 10 days, with possible extra work to eaves, window and door surrounds and pipework. IWI means clearing walls, removing radiators, sockets, skirting boards and door frames, then replacing and redecorating. The same guidance notes that IWI can be phased room by room within a longer plan, which suits landlords working between tenancies and owners who decorate one room at a time.
Space
IWI at around 100mm thick reduces floor area. Thinner boards lose less. Government-linked guidance and trade bodies quote 25mm to 100mm per wall, and SWIGA notes build-ups of up to around 150mm in some systems. In a small bedroom or a narrow hall that is noticeable, so measure before you decide.
Appearance and planning
EWI changes the look of the house and may need planning permission. Rainwater goods must be removed, and roof junctions and openings may need adapting as the wall gets thicker. Listed buildings need consent, and one local authority’s guidance says EWI is more likely to be accepted on less visible facades than on principal elevations. IWI leaves the exterior alone, which is why it is the usual answer in conservation areas and for period frontages.
External wall insulation and damp
This is the question behind the second search query: does external wall insulation cause damp, or cure it?
Properly designed and fitted, EWI helps. It keeps the masonry warm and shields it from rain. Because it keeps structural elements warm, it reduces thermal bridging and external moisture reaching the fabric. The same source adds that EWI becomes the building’s main weatherproofing layer, so a weakness in its design, detailing or installation can cause significant failures.
The mechanism is worth understanding. An uninsulated solid wall has no dew point inside it in the way an insulated one does. Adding EWI creates a dew point outside the masonry. If the insulation has gaps or thin spots around windows, doors or pipes, the dew point can fall inside the masonry in those places and produce damp patches. Full, continuous coverage, a breathable system and sound heating and ventilation are what prevent that.
IWI leaves the masonry on the cold side, so moisture levels in the wall generally rise unless the build-up is chosen for the wall. The government guide sets out how to do that: the lowest-risk designs for traditional solid walls are moisture-open build-ups using capillary-active insulation such as woodfibre, vapour-open finishes and an air barrier, with no vapour barrier. It also says the assessment must consider orientation, wind-driven rain zone, exposure, wall construction, internal moisture loads, ground conditions and the condition of external finishes.

In short, either system can be damp-safe, and either can fail on a wall that was not understood first.
Fix the damp before you insulate
Both systems share one rule. Damp has to be dealt with first.
- The government’s IWI guide states that damp sections of existing construction must be allowed to dry thoroughly before installation, and the building re-assessed.
- SWIGA says existing cracking, penetrating or rising damp and poor mortar joints need to be fixed before IWI is installed.
- Local authority planning guidance says any evidence of damp in the walls must be resolved before insulation is applied.
The common causes on a solid-wall home are rising damp from a failed or missing damp-proof course, penetrating damp through defective pointing, gutters or roofs, and condensation from poor ventilation. Each calls for a different remedy. Insulation does not repair any of them, and it hides the signs that would have shown you the fault.
A useful check before you ask for insulation quotes: look for tide marks, salts or flaking plaster at the base of walls, damp patches near gutters and chimneys, and black mould in corners and behind furniture. If you see any of these, get the wall surveyed first. Our guide on how to fix damp that keeps coming back on internal walls explains why treating the symptom fails.
When each system is the better fit
Guidance from the Sustainable Development Foundation states that EWI should be considered first unless planning issues, heritage value or building complexity favour IWI, because it is more thermally efficient, less disruptive and carries a lower condensation risk. That is the starting rule, and in practice many properties in this region fall into the exceptions.
IWI is usually the answer when:
- the property is in a conservation area, is listed, or has a period facade worth keeping;
- the wall sits on or close to a boundary, or the neighbor’s access is a problem;
- it is a flat, or the freeholder or leaseholder arrangement rules out external work;
- a landlord wants to work one room at a time between lets;
- scaffolding and render would push the cost beyond the budget.
The Retrofit guidance from a government-backed body lists the same cases: IWI is the key option where EWI is ruled out by cost, planning constraints, leasehold issues, high-rise blocks, access costs or external features.
EWI is usually the answer when:
- the walls are plain, accessible and free of planning limits;
- you want to keep every square foot of internal space;
- the household cannot move out of rooms or redecorate;
- the render itself needs renewing and the work can be combined.
There is no standard off-the-shelf solution. The government’s innovation report notes that wall construction, materials and layouts differ so much that no single best practice applies to every property, and that experts disagree most on moisture risk. That is the case for specifying wall by wall.
Regulations to know about
Insulating a wall is building work. One architectural guide states that all EWI work must be notified to Building Control, with registered installers able to self-certify, and that where EWI covers more than half a wall or a quarter of the building envelope, the whole affected element should be upgraded towards a U-value of 0.30 W/m²K. A U-value measures how fast heat passes through a wall: the lower the figure, the better it insulates.
For older solid walls, a thinner build-up can be a sensible compromise. The Alliance for Sustainable Building Products notes that Part L allows a threshold of up to 0.70 W/m²K for existing walls where payback is under 15 years, and that 40mm of natural fibre IWI reaches about 81% of the energy saving of the 0.30 target, while 60mm reaches about 90%. That balances savings against moisture risk and room space, and it is the reasoning behind the “two-thirds rule” readers sometimes ask about.
If you are in England and the property is listed, check with the local authority before any external work. Rules differ in Wales, Scotland and Northern Ireland.
A worked example: a 1930s solid-wall semi
Take a three-bed solid-wall semi with a damp patch low on the party-side wall and mould in the main bedroom corner.
- Survey. A specialist checks moisture readings, the damp-proof course, pointing, gutters and ventilation, and separates rising damp, penetrating damp and condensation.
- Repair. The cause is treated, for example a failed damp course, defective pointing or a leaking downpipe, and the wall is given time to dry.
- Choose the system. If the front is unrestricted and the household wants no loss of space, EWI is considered first. If the front must keep its brickwork, or the household prefers to work room by room, IWI is specified.
- Cost it. On MoneySuperMarket’s averages, that is about £11k for EWI or about £7k for IWI on a three-bed semi. Real quotes should be itemised by wall.
- Install and ventilate. Whichever system is used, heating and ventilation must keep moisture in check afterwards.
Savings follow the system. A government comparison of 2,411 homes, summarized by Retrofit Planner, found a median 17.3% fall in gas use after solid wall insulation. Energy Saving Trust figures quoted by SWIGA put EWI on a detached house at about 1.8 tonnes of CO2 and about £435 a year. Fuel prices move, so the pound value of any saving changes with each price cap period.
Starting with a survey
The sequence above explains why a damp specialist is the right first call for a solid-wall property with signs of moisture. Proofterior is a specialist contractor treating damp, mould and timber problems across Dorset, Hampshire and Wiltshire. Its diagnostic approach looks for the root cause so that treatment is tailored, not guessed.
The survey is complimentary and is followed by a detailed written report. Treatment is carried out by in-house specialists rather than subcontractors, and all treatment work carries a 25-year insurance-backed guarantee. Work is PCA aligned and accredited.
Where internal insulation is the right fit, Proofterior installs IsoTherm wall insulation, and its projects show how damp treatment and insulation are combined, such as damp proofing with IsoTherm internal wall insulation in Southampton and mould and condensation in a Bournemouth bedroom. For wider upgrades, see energy efficiency upgrades in Dorset.
To book a survey, use the complimentary property survey page.

Estate agents, landlords and property managers can use the same route to get a written record of a wall’s condition before a sale, a letting or a refurbishment.
Our view on EWI, IWI and damp
Most of the insulation failures we are asked to look at share a starting point: the wall was insulated before anyone had worked out why it was damp. The system chosen is rarely the root of it.
Our approach is to survey first, write down what we find and treat the cause. Only then does the insulation question have a sound answer. On a solid-wall home that has suffered rising damp, penetrating damp or condensation, internal insulation fitted as part of a complete damp-proofing scheme lets each room be treated, dried and finished in turn, and keeps the street-facing elevation as it was built.
Because our own specialists carry out the diagnosis and the treatment, the person who identified the problem is accountable for the remedy. That is why we back treatment work with a 25-year insurance-backed guarantee.
Dylan
FAQ
Can external wall insulation cause damp?
Poorly fitted EWI can. Gaps or thin areas around windows, doors and pipes create cold spots where condensation and damp patches form. Full coverage, a breathable system and a dry wall at the start are what prevent it, which is why a survey comes before the scaffolding. If you already have damp showing, treat that first.
Is planning permission needed for EWI or IWI?
IWI does not change the exterior, so it rarely raises planning issues, though listed buildings need consent for any alteration affecting their character. EWI alters the appearance and may need planning permission, and Listed Building Consent is required for listed properties. Ask your local planning authority before you commit.
Which is cheaper, EWI or IWI?
IWI usually is. Published averages put IWI at £4k to £13k and EWI at £6k to £22k, with a three-bed semi at roughly £7k and £11k. The gap narrows once repairs, redecoration and refitting radiators are included, so compare itemized quotes for the same walls.
Can I insulate only some walls?
Yes, and IWI is well suited to it because it can be done room by room. Be aware that where more than half a wall is insulated, building regulations expect the whole wall to be upgraded where feasible. Partial insulation also needs thought at the junctions, where cold spots can appear.
Sources
- The Different Solid Wall Insulation Systems, SWIGA
- External Wall Insulation Costs 2026, BuilderQuote
- How do I insulate solid walls?, Lime Knowledge Base
- Retrofit Internal Wall Insulation: guide to best practice, GOV.UK
- Solid Wall Insulation, Sustainable Development Foundation
- Solid wall insulation, MoneySuperMarket
- Solid wall insulation costs and savings, Which?
- Externally applied solid wall insulation, Bath and North East Somerset Council
- Retrofit materials and permeability, September 2025
- External Wall Insulation: A Guide to Retrofitting Homes, Designs in Detail
- Best Practice and Innovation, BEIS
- Solid Wall Insulation guidance, Bristol
- Insulation and retrofit: finding the sweet spot, ASBP
- Solid Wall Insulation Cost UK, Retrofit Planner




